其他编程

h3c路由器配置命令,思科路由器配置命令

H3C 路由器配置命令一、路由器基本配置命令 1、system-view 进入系统视图模式 2、sysname R1 为设备命名为 R 3、display ip routing-table 显示当前路由表 4、language-mode Chinese

English 中英文切换 5、interface Ethernet 0/0 进入以太网端口视图 6、ip address 192.168.1.1 255.255.255.0 配置 IP 地址和子网掩码 7、undo shutdown 打开以太网端口 8、shutdown 关闭以太网端口 9、quit 退出当前视图模式 10、ip route-static 192.168.2.0 255.255.255.0 192.168.12.2 description To.R2 配置静态路由 11、ip route-static 0.0.0.0 0.0.0.0 192.168.12.2 description To.R2 配 置默认的路由 基本配置案例[Quidway]display [Quidway]display [Quidway]display [Quidway]display version current-configuration interfaces ip route 显示版本信息 显示当前配置 显示接口信息 显示路由信息 更改主机名 设置口令 进入接口 激活端口 绑定 hdlc 协议[Quidway]sysname aabbcc [Quidway]super passwrod 123456 [Quidway]interface serial0 [Quidway-serial0]ip address [Quidway-serial0]undo shutdown [Quidway]link-protocol hdlc[Quidway]user-interface vty 0 4 [Quidway-ui-vty0-4]authentication-mode password [Quidway-ui-vty0-4]set authentication-mode password simple 2 [Quidway-ui-vty0-4]user privilege level 3 [Quidway-ui-vty0-4]quit [Quidway]debugging hdlc all serial0 [Quidway]debugging hdlc event serial0 [Quidway]debugging hdlc packet serial0 显示所有信息 调试事件信息 显示包的信息静态路由配置案例: [Quidway]ip route-static {interfacenumber

nexthop}[value][reject

blackhole] 例如: [Quidway]ip [Quidway]ip [Quidway]ip [Quidway]ip route-static route-static route-static route-static 129.1.0.0 16 10.0.0. 129.1.0.0 255.255.0.0 10.0.0. 129.1.0.0 16 Serial 0.0.0.0 0.0.0.0 10.0.0.动态路由配置案例(RIP): [Quidway]rip [Quidway]rip work [Quidway]rip input [Quidway]rip output [Quidway-rip]network 1.0.0.0 [Quidway-rip]network 2.0.0.0 [Quidway-rip]peer ip-address [Quidway-rip]summary [Quidway]rip version [Quidway]rip version 2 multicast [Quidway-Ethernet0]rip split-horizon;可以 all;水平分隔动态路由配置案例(OSPF): [Quidway]router id A.B.C.D 配置路由器的 ID [Quidway]ospf enable 启动 OSPF 协议 [Quidway-ospf]import-route direct 引入直联路由 [Quidway-Serial0]ospf enable area 配置 OSPF 区域 标准访问列表命令格式如下: acl [match-order config

auto] 默认前者顺序匹配。 rule [normal

special]{permit

deny} [source source-addr source-wildcard

any] 例: [Quidway]acl 10 [Quidway-acl-10]rule normal permit source 10.0.0.0 0.0.0.25 [Quidway-acl-10]rule normal deny source any 二、ACL 配置 扩展访问控制列表配置命令1.配置 TCP/UDP 协议的扩展访问列表:rule {normal

special}{permit

udp}source {

any}destination

any} [operate] 2.配置 ICMP 协议的扩展访问列表: rule {normal

special}{permit

deny}icmp source {

any]destination {

any][icmp-code] [logging] 扩展访问控制列表操作符的含义 equal portnumber 等于 greater-than portnumber 大于 less-than portnumber 小于 not-equal portnumber 不等 range portnumber1 portnumber 区间3.扩展访问控制列表案例[Quidway]acl 10 [Quidway-acl-101]rule deny souce any destination any [Quidway-acl-101]rule permit icmp source any destination any icmp-type echo [Quidway-acl-101]rule permit icmp source any destination any icmp-type echo-reply [Quidway]acl 10 [Quidway-acl-102]rule permit ip source 10.0.0.1 0.0.0.0 destination 202.0.0.1 0.0.0.0 [Quidway-acl-102]rule deny ip source any destination any [Quidway]acl 103 [Quidway-acl-103]rule permit tcp source any destination 10.0.0.1 0.0.0.0 destination-port equal ftp [Quidway-acl-103]rule permit tcp source any destination 10.0.0.2 0.0.0.0 destination-port equal www [Quidway]firewall enable [Quidway]firewall default permit

deny [Quidway]int e0 [Quidway-Ethernet0]firewall packet-filter 101 inbound

outbound 4. NAT 的配置 地址转换配置案例 [Quidway]firewall enable [Quidway]firewall default permit [Quidway]acl 10 [Quidway-acl-101]rule deny ip source any destination any [Quidway-acl-101]rule permit ip source 129.38.1.4 0 destination any [Quidway-acl-101]rule permit ip source 129.38.1.1 0 destination any [Quidway-acl-101]rule permit ip source 129.38.1.2 0 destination any [Quidway-acl-101]rule permit ip source 129.38.1.3 0 destination any [Quidway]acl 10 [Quidway-acl-102]rule permit tcp source 202.39.2.3 0 destination202.38.160.1 0 [Quidway-acl-102]rule permit tcp source any destination 202.38.160.1 0 destination-port great-than 1024 [Quidway-Ethernet0

Similar Posts

发表评论

邮箱地址不会被公开。 必填项已用*标注